Filter
Shopping Options
-
In stock
Pro Touch Bar 15" (A1707)- LCD Display Flex Cable To MotherBoard Screws (Torx T3) (2 pieces set) Compatible For Macbook Pro 13" W/ Touch Bar (A1708 / A2159 / A2289 / A2338 / A1706 / A1707 / A1989 / A1990 / A2251/ Late 2016 to Late 2020) (50 Pack)
- iPhone is a trademark of Apple Inc., registered in the U.S. and other countries and regions.
-
In stock
Pro Touch Bar 15" (A1707)- High quality CPU Fan Screws Torx T5 for Macbook Pro 13".
- These screw will keep hold your fan from flying away.
- The fan is secured to the top case underneath the logic board.
- Replace lost CPU Fan Screws with our best quality product for Macbook.
- Every Part is tested before shipping.
- Part Numbers: 923-01174
- Related Numbers: 923-01168
Compatible with :
- Pro 13 (A1708, Late 2016/ Mid 2017)
CPU Fan Screws (Torx T5) (4 Piece Set) -
In stock
Pro Touch Bar 15" (A1707)- Vent / Antenna Module Screws (Pentalobe P2) For MacBook Pro 13" Retina.
- These screws secure the rear vent and antenna module to the top case.
- If you lost Screws than buy our new Screws set for you Macbook.
- You'll need a Screwdriver with a security bit to install these screws
- Part Numbers: 923-01191
- Printed Numbers: 923-01169
Compatible with :
- Pro 13 Retina (A1708, Late 2016 / Mid 2017)
Vent / Antenna Screws (Pentalobe P2) (12 Piece Set) -
In stock
Pro Touch Bar 15" (A1707)- These screws secure the TCON (Timing controller board) to the display assembly and rear vent.
- We may have a few loose screws, but you don't need to!
- Two screws have shoulders, and are used on the outer ends of the TCON board.
- Part Numbers: 923-01277, 923-01282.
Compatible with :
- Pro 13 (A1708, Late 2016/ Mid 2017).
TCON Board Screws (Torx T4) (4 Piece Set) -
In stock
Pro Touch Bar 15" (A1707)- High-Quality Bottom Case Screws (Pentalobe P5) For MacBook Pro 15" W/ Touch Bar (A1707: Late 2016/Mid 2017) (A1990 Late 2018/Early 2019) (Silver)
- Secure your bottom (case) with this screw set.
- We may have a few loose screws, but you don't need to!
- Two long screws for the rear corners and four short screws for the sides and front.
- The long screws go in the rear corners.
- Part Numbers: 923-01513, 923-01514, 923-01516, 923-0151
Compatible with :
- MacBook Pro 15 (A1707, Mid 2017 / Late 2016)
- MacBook Pro 15 (A1990, Mid 2018 / Mid 2019)
SilverBottom Case Screws (Pentalobe P5) -
In stock
Pro Touch Bar 15" (A1707)- High-Quality Bottom Case Screws (Pentalobe P5) For MacBook Pro 15" W/ Touch Bar (A1707: Late 2016/Mid 2017) (A1990 Late 2018/Early 2019) (Space Gray)
- Secure your bottom (case) with this screw set.
- We may have a few loose screws, but you don't need to!
- Two long screws for the rear corners and four short screws for the sides and front.
- The long screws go in the rear corners.
- Part Numbers: 923-01513, 923-01514, 923-01516, 923-0151
Compatible with :
- MacBook Pro 15 (A1707, Mid 2017 / Late 2016)
- MacBook Pro 15 (A1990, Mid 2018 / Mid 2019)
SPACE GRAYBottom Case Screws (Pentalobe P5) -
In stock
Pro Touch Bar 15" (A1707)- These screws secure the trackpad cable cowling to the logic board.
- We may have a few loose screws, but you don't need to!
- Two screws are needed to ensure the cowling stays on properly.
- All parts tested and working just like they were when you bought your MacBook..
- Part Numbers: 923-01281.
Compatible with :
- Pro 13 (A1708, Late 2016/ Mid 2017).
Touchpad Cable Cowling Screw (1 Bracket+2 Screws) (Torx T5) -
In stock
Pro Touch Bar 15" (A1707)- Best quality Headphone Jack for Macbook Pro 15 Touch Bar A1707.
- This Headphone Jack is used to listen sound from Ear-phone wire.
- Replace damaged or non-working Headphone Jack with this part for Macbook Pro.
- All parts tested and working just like they were when you bought your MacBook.
- Printed Number: 821-00616-04.
Compatible with :
- Pro 15 (A1707, Late 2016 / Mid 2017).
SPACE GRAYHeadphone Jack -
In stock
Pro Touch Bar 15" (A1707)- This is a replacement power button and touch ID cable for the MacBook Pro 15 with Touch Bar.
- All parts tested and working just like they were when you bought your MacBook..
- Printed Number: 821-00645-03.
Compatible with :
- Pro 15 (A1707, Late 2016 / Mid 2017).
- Pro 15 (A1990, Late 2018 / Early 2019).
Power Button Connecting Cable (Connect To Motherboard) -
In stock
Pro Touch Bar 15" (A1707)- This is a replacement Heatsink for the MacBook Pro 15
- Keeps the CPU, GPU, and PCH from overheating.
- All parts tested and working just like they were when you bought your MacBook.
Compatible with :
- Pro 15 (A1707, Late 2016 / Mid 2017).
- Pro 15 (A1990, Late 2018 / Early 2019).
Heat Sink -
In stock
Pro Touch Bar 15" (A1707)- This is a replacement right fan for the MacBook Pro 15 with Touch Bar.
- This one little fan keeps your whole computer cool!
- The fan flex cable is included and attached to the fan.
- All parts tested and working just like they were when you bought your MacBook..
- Part Numbers: 923-01471.
Compatible with :
- Pro 15 (A1707, Late 2016 / Mid 2017).
- Pro 15 (A1990, Late 2018 / Early 2019).
Right Fan -
In stock
Pro Touch Bar 15" (A1707)- High-Quality Left & Right Fan For MacBook Pro 15" w/ Touch Bar (A1707: Late 2016/Mid 2017) (A1990 Late 2018/Early 2019)
- Replace noisy or damaged cooling fans to keep your MacBook Pro happy and healthy..
- The fans are the only moving parts in the MacBook Pro 15-inch with Touch Bar, so if you're hearing abnormal sounds coming from within, it's got to be the fans.
- Part Numbers: 923-01459, 923-01471
- Printed Part Numbers: MG70050V1-C150-S9A, MG70050V1-C167-S9A
Compatible with :
- MacBook Pro 15 (A1707, Mid 2017 / Late 2016)
Left & Right Fan -
In stock
Pro Touch Bar 15" (A1707)- Best quality Display Gasket for Macbook Pro 15 A1707 / A1990.
- Gasket fits around the outside edge of the display assembly.
- Replace damage Display Gasket with our part for Macbook.
- it’s made from quality material and precision machining.
Compatible with :
- Pro 15 (A1707, Late 2016 / Mid 2017).
- Pro 15 (A1990, Late 2018 / Early 2019).
Display Gasket -
In stock
Pro Touch Bar 15" (A1707)- Best quality Clock Generator Controller IC for MacBooks (Silego).
- This chip creates the clock signals like SYSCLK_CLK32K_RTC and also the PPVRTC_G3H power rail.
- It is often placed on the corner of the board making it susceptible to liquid damage & death.
- SLG3NB148CV does NOT work with SLG3NB148V or SLG3NB148A - buy the right chip! SLG3NB148V & SLG3NB148A are interchangeable which is what comes if you buy this.
- All Macbook Motherboard Parts are made from best quality materials.
- Ask for Professional Installation.
- Part Numbers: U2600 / U2700 / U2800.
- Compatible Boards: 820-3023 820-3332 820-3024 820-3208 820-3462 820-3330 820-2915 820-2914 820-3115 820-2936
- Pin Numbers: QFN-16 Pin
PPVRTC_G3H Power & AMP SYSCLK_CLK32K_RTC Clock Generator Controller IC -
In stock
Pro Touch Bar 15" (A1707)- The TPS62510 is a high-efficiency step-down converter targeted for operation from a 1.8-V to 3.8-V input voltage rail, ideally suited for 2-cell alkaline or NiMHd applications.
- The TPS62510 is also ideal as a point-of-load regulator running from a fixed 3.3-V, 2.5-V, or 1.8-V input voltage rail
- The converter operates in fixed frequency pulse width modulation (PWM) mode switching at 1.5 MHz with the MODE pin high.
- Pulling the MODE pin low enables the high efficiency mode. In high efficiency mode, the device operates with a 1.5-MHz fixed frequency PWM at nominal load current, and automatically enters the power save mode at light load currents.
DC To DC Converter And Switching Regulator Converter IC -
In stock
Pro Touch Bar 15" (A1707)- It measures the voltage developed across an external sense resistor to represent the high-side current of a battery or voltage regulator.
- It also measures the bus voltage and uses these measured values to present a proportional power calculation.
- The EMC1704 contains additional bidirectional peak detection circuitry to flag instantaneous current spikes with programmable time duration and magnitude threshold.
- Printed Number: SMSC1704-2, EMC1704-2
High-Side Current Sensinsory Temperature Measurement Controller IC -
In stock
Pro Touch Bar 15" (A1707)- Top Quality Synchronous Buck Regulator IC for MacBooks (INTERSIL,ISL8009BIRZ / ISL8009B / 8009B / 8009 / 09B,QFN-8 Pin).
- Replace damaged or non-working Synchronous Buck Regulator IC with this part for Macbooks.
- All Macbook Motherboard Parts are made from best quality materials.
- Ask for Professional Installation.
- Part Numbers: ISL8009BIRZ.
- Printed Numbers: 8009B / 8009 / 09B
- Pin Numbers: QFN-8 Pin
Synchronous Buck Regulator IC -
In stock
Pro Touch Bar 15" (A1707)- High-Quality CPU / GPU Power IC For MacBook Pro Retina 13" / Pro 15"(A1706 / A1707 / A1708:Late 2016 / Mid 2017) (NTERSIL: SL95828HRTZ / ISL95828:U7100: QFN-48 Pin)
- This IC regulates power to the CPU and GPU..
- You might know this part as a buck controller, power management controller, or just plain ol' power chip..
- Part Numbers: 353S00928, U7100
- Printed Part Numbers: ISL95828HRTZ
Compatible with :
- MacBook 12" Retina (A1534, Early 2016 / Mid 2017)
- Air 13 (A1932, Mid 2019 / Late 2018)
- MacBook Pro 13" (A1706, Mid 2017 / Late 2016)
- MacBook Pro 13" (A1708, Mid 2017 / Late 2016)
- MacBook Pro 15" ( A1707, Mid 2017 / Late 2016)
- MacBook Pro 13" (A1989, Mid 2018 / Mid 2019)
- MacBook Pro 15" (A1990, Mid 2018 / Mid 2019)
- MacBook Pro 13" ( A2159)
CPU / GPU Power IC -
In stock
Pro Touch Bar 15" (A1707)- Best quality Clock Generator Controller IC for MacBooks (Silego).
- This chip creates the clock signals like SYSCLK_CLK32K_RTC and also the PPVRTC_G3H power rail.
- It is often placed on the corner of the board making it susceptible to liquid damage & death.
- SLG3NB148CV does NOT work with SLG3NB148V or SLG3NB148A - buy the right chip!
- All Macbook Motherboard Parts are made from best quality materials.
- Ask for Professional Installation.
- Part Numbers: U1900.
- Compatible Boards: 820-00165 820-3437 820-3662 820-3787 820-3435 820-00164 820-3476 820-3536 820-4924
- Pin Numbers: QFN-16 Pin
PPVRTC_G3H Power & AMP SYSCLK_CLK32K RTC Clock Generator Controller IC -
In stock
Pro Touch Bar 15" (A1707)- The MAX98300 mono 2.6W Class D amplifier provides Class AB audio performance with Class D efficiency.
- This device offers five selectable gain settings (0dB, 3dB, 6dB, 9dB, and 12dB) set by a single gain-select input (GAIN).
- Active emissions-limiting edge-rate and overshoot control circuitry greatly reduces EMI.
- A filter less spread-spectrum modulation scheme eliminates the need for output filtering found in traditional Class D devices. These features reduce application component count.
- The MAX98300 industry-leading 0.78mA at 3.7V (1.1mA at 5V) quiescent current extends battery life in portable applications.
- The MAX98300 is available in an 8-pin TDFN-EP (2mm x 2mm x 0.8mm) and a 9-bump (1.2mm x 1.2mm) WLP.
- Parts Number: U6610
- Printed Number: MAX98300E
Compatible with :
- Pro Unibody 13 (A1278 / Early 2011 / Late 2011 / Mid 2012)
Audio Amplifier IC -
In stock
Pro Touch Bar 15" (A1707)- The ISL6208 is a High Frequency, Dual MOSFET Driver, Optimized to Drive Two N-channel Power MOSFETs in a Synchronous-rectified Buck Converter Topology.
- It is Especially Suited For Mobile Computing Applications That Require High Efficiency And Excellent Thermal Performance.
- This Driver, Combined With an Intersil Multiphase Buck PWM Controller.
- Forms a Complete Single-stage Core-voltage Regulator Solution For Advanced Mobile Microprocessors.
High Voltage Synchronous Rectified Buck MOSFET Controller IC -
In stock
Pro Touch Bar 15" (A1707)- Top Quality Synchronous Power Buck Controller IC for MacBooks (TI, CSD87330Q3D / 87330D / 873300 / 87330Q / 87330, QFN-8 Pin).
- Replace damaged or non-working Synchronous Power Buck Controller IC with this part for Macbooks.
- All Macbook Motherboard Parts are made from best quality materials.
- Ask for Professional Installation.
- Part Numbers: CSD87330Q3D.
- Printed Numbers: 87330D
- Pin Numbers: QFN-8 Pin
Synchronous Power Buck Controller IC -
In stock
Pro Touch Bar 15" (A1707)- The TPS720 family of dual rail, low-dropout linear regulators (LDOs) offers outstanding performance (PSRR, load, and line transient response) while consuming a very low quiescent current of 38 µA..
- The TPS720 supports a novel feature in which the output of the LDO regulates under light loads when the IN pin is left floating
- The light-load drive current is sourced from VBIAS under this condition. This feature is particularly useful in power-saving applications where the DC-DC converter connected to the IN pin is disabled but the LDO is still required to regulate the voltage to a light load..
- The TPS720 is stable with ceramic capacitors and uses an advanced BICMOS fabrication process that yields a dropout of 110 mV at a 350-mA output load
- The TPS720 has the unique feature of providing a monotonic VOUT rise (overshoot limited to 3%) with VIN inrush current limited to 100 mA + ILOAD with an output capacitor of 2.2 µF...
- Parts Number: TPS720105DRVR, TPS720105
PMIC Voltage Linear Regulators Controller IC
